More work on the F-706 bulkhead - 3 hours

I haven't been feeling well lately so I've not been very motivated to get in the garage a work away. I managed to put in some hours today and advance the F-706 bulkhead. I completed drilling the F-728B angle to the 728A rib. All that was left was to drill the 1/4" holes for the bellcrank assembly. This was a head scratcher for me as how best to do this. 1/4" hole is fairly large to get centered with only the hole in the rib skin as a guide.
 
I decided to make a jig with a piece of oak. this will allow me to start a centered hole with a hand drill and then I can finish it on the drill press.

I used the 1/4" drill bit to ensure center of the holes. 


I then clamped the oak to the web and double checked hole alignment.



I clecoed on the angles to the web and then used the hand drill to start the 1/4" hole.

I double checked centering of the pilot and it was looking great. So I finished the 1/4" hole in the drill press.

Both holes turned out perfect.

I then completed the match drilling of F-705B/F-730/F-728/F-729. All I need to do now is debur, break edges, 3M, clean and prime. I'll save that for another day when I'm feeling better.  

Working away on the F-706 Bulkhead - 3.5 hours

I received new 0.63" 3/4" x 3/4" angle a few days ago so I can recut the F-729B angle and make the F-728B angle. I was really stumped by the 1/8" diameter hole callout on the F-728B piece and then it occurred to me that this was the initial hole for the first cleco to attach the angles to the webs. When working on the F-729B and F-729C pieces I thought that he 1/8" holes were to match up. And technically that's half true. Turns out that the 1/8" hole is a pilot hole for F-729C to attach to F-728B. However the 1/8" hole in F-728B is for the first cleco to the 728A rib. This is why I was having edge distance issues when using the Van's Dimension given for the overall length (24-5/32"). Silly me. Of course I figured this out after I drilled the 1/8" hole for my new F-729B angle, so I just have to roll with it. In the end, I recut the F-729B angle and managed to get all those pieces fit together and holes perfectly aligned with excellent edge distance. It just took me way longer than necessary.

I began assembling the pieces as per Drawing 26. however, I noticed that the webs and pieces weren't sitting parallel. I was unsure about the final fitment at this point.

I disassembled the pieces and drilled the F-729A and B pieces together. Next, to ensure the most correct alignment, I clecoed the assembly/ribs to the bottom fuselage skin to ensure all piece where in the correct position. Once I was happy with fitment I then drilled the F-730/F-729C.


I have the 1/8" holes aligned. I will final drill these to #30 when I am ready to rivet.

I have excellent edge distances on the F-729A angle.

Finishing up the F-705 Bulkhead - 2 hours

Tonight, I bolted the seatbelt anchors onto the bulkhead and torqued them. I also installed the nutplates on the side of the bulkhead (with NAS1097 rivets).

 Next I began to setup to drill the plastic flap bearing blocks. I installed both blocks on the bulkhead and measured each side to ensure that they were parallel.


Once I was sure that both were in the correct location, I clamped them and checked twice.


Once I was happy with the setup, I used the palm drill to start a pilot hole with the #12 bit. I then set up the drill press to complete the holes.

When finished drilling, on inspection. The holes didn't line up, the new hole seemed to be crooked. Really weird. It bugged me for quite a while, and then as soon as I put the blocks together....I figured out what happened.

The blocks from Vans are not cut straight at the factory...one block is at a slight angle when placed on a flat surface. So depending on how it sat when I drilled it....the holes were not going to be "Straight". Ugh...what a silly Gotcha. I will order a couple new flap blocks and drill it again. I will have to be careful to ensure that they are both straight to begin with before drilling.

Finished riveting the F-705 bulkhead - 2 hours

Again, another small night on the build. Ugh....work gets in the way too much. I clamped the F-705 bulkhead to the table and finished squeezing the remaining AD4 rivets. Note that I did not attach the F-705F channel crosspiece as I am fitting the Anti-Splat Almost an RV14 mod during my build.

Started Riveting F-705 Bulkhead - 2 hours

I managed to squeeze in a small amount of work tonight. I began riveting the lower portion of the F-705 bulkhead. I decided to buck these rivets since with a proper setup, I have really good success setting straight and virtually perfect rivets. The pictures don't show it well, but I stand the bulkhead vertical and clamp it to the wood uprights on the edge of my table. I then have excellent access to buck all the rivets along the bottom.

All finished for the night, just will need to squeeze the rest as the material is too thin to buck the other rivets.

Primed F-705 bulkhead parts - 2 hours

Work has been so awfully busy I just haven't had any time to get working on the fuse. Today I managed to get a little time in and I prep'd and primed the F-705 Bulkhead parts. 

Started F-706/F-707 and F-708 Bulkheads - 7 hours

I started the day with digging out the F-706, 707 and 708 bulkhead parts. I began the work by fluting and trying to straighten all the pieces. The F-706 pieces are the worst offenders and are very warped and difficult to straighten. They are not perfectly flat, and at the advice of some local builders, there is little point in trying to make them perfect now as they will likely need more adjustment later when fitting the skins.



The tight corners need a fair amount of work as the tabs either touch or overlap. In the case of the 706 bulkhead they overlapped during forming so they really need work.






I see that some chose to cut these tabs down, while I choose to file them in order to preserve as much material as I could. I have a very small and thin file which I used to remove the conflicting material. I then re-rounded the tab corners and fixed what needed it. I broke all the edges and they are ready to 3M. Lots of time went into cleaning these up.
I drilled all the openings with the unibit for the rudder cables as well. I focused on the F-706B bulkhead. I see from everyone's build logs that the 5/8" holes in the center end up causing quite the issue with edge distances from the holes. After a bit of head scratching. I decided to reduce the hole size to 7/16". Since I am going with electric trim, there is no reason I see at this time to open up the holes to the maximum opening....so why do it. At 7/16" I can fit a smaller grommet for wiring and have tons of room for edge distance.



I really took my time and didn't rush the job and It turned out extremely well.
Next I moved onto the F-729A,B and C pieces. I soon found out that I must have cut too much of my 6' length of 0.63 angle so I don't have a 36" piece for 728B. Oh well, minor and its cheap to order more. I went to work on F-729C. Getting it bent to 88.5deg was quite easy. Just a light tap with the rubber mallet in the vice and it was enough.

Next I set up the pieces so I could fit and drill the 1/8" hole.


Looking good here. 

 I realized after the fact that the F-729B has edge distance issues on the aft end when I cut it per the dimensions in the plans. The angle needs to be a fair amount longer. I will have to re-do this piece as well. Not so good here. Edge distance on the last hole becomes a problem and there is lots of room till the flange. I will consider making the piece longer, and then rounding the end of the angle to fit the bend in the flange.